4.3也就是上周，思博(spoto)学员于布鲁塞尔（Brussels）一次pass！
lab详解和心得，了解一下{:soso__12206632511069352580_4:}
TS1,H3++,H2+
Hi All Friends, Many Thanks Spoto Teams for always support & follow up all process of My Exam. This is my first attempt (TS1,H3++,H2+) And Finally I got my magic Number with Spoto solution & every feedback form our group (All feedback this important is help you for learning form some mistake) TS1 ( Completed : 1 Hrs. with Recheck) Q1. SW2 >> int valn 100 wrong IP address Q2. R12 >> int s4/0 peer default was missing (need to used peer with DHCP Pool) Q3. R3 >> area range need to remove R5 >> max-metric router-lsa need to remove Q4. R13 >> prefix-list configured blocking 145.14.14.14 network, just make permit Q5. R5 >> need to active Ipv4 neighbor with 123.4.4.4 R21 >> wrong prefix-list , need to add 194.1.0.0/16 le 32 R21 >> neighbor PEER route-map LP in (I changed to neighbor PEER route-map LP out for match the output ) Q6. R22 >> need to create Route-map ( ipv6 next-hop) and add route-map in neighbor Q7. R15 >> ip nhrp redirect that missing R18 >> ip nhrp multicast that missing R19 >> ACL DMVPN need to permit esp any any Q8. R7 >> neighbor 123.45.67.21 need to configure default-information originate R7 >> need to change static route to ip route 0.0.0.0 0.0.0.0 125.45.67.21 R8 >> int e0/0.123 need to apply ip nat inside Q9. I do not anything the output was match Q10. R23 >> neet to change ACL permit ip 192.168.1.0 0.0.0.255 any
Diagnostic H3++ ( Completed : 10 Minute with Recheck this section can’t click bottom for end exam) Part 1 Q1 >> Used filter “bootp” and choose the first seq: 114 Q2 >> Its source IP Address is 0.0.0.0 Q3 >> SW1-SW3 Part 2 (Used filter “http.request.method==GET”) Q1 – Q3 >> Same spoto Diagnostic H2+ ( Completed: 5 Hrs. with recheck ) Section 1.1 >> vtp is already configure just verify only spanning-tree portfast edge default spanning-tree portfast edge bpduguard default Section 1.2 >> Same spoto Section 1.3 >> Same spoto Section 1.4 >> Same spoto Section 2.1 >> Datacenter no have any config of OSPF need to do. I apply ip ospf network point-to-point all int vlan R17 have preconfig interface vrf Corp and need to configure ospf Headquarter & Core preconfig ospf already except R9 & R10 need to recheck all Another same spoto
Section 2.2 >> Same spoto Section 2.3 >> Same spoto but question do not change any metric in EIGRP but I configure with spoto solution the output was match (metric rib-scale 153) and need to config advertise network lo0 in router eigrp (R50-R54) Section 2.4 >> ibgp same spoto ebgp same spoto have preconfig bgp but configure only router-id,allwas-in, aggregate, default-originate (R15,R16), and redistribute need to configure vrf and rd follow spoto solution Section 2.4 >> ibgp same spoto ebgp same spoto but configure only router-id,allwas-in, aggregate, default-originate (R15,R16) need to configure vrf and rd follow spoto solution Section 2.5 >> Same spoto have preconfig bgp but configure only router-id , aggregate, and redistribute need to check ip interface between 52<>58 is incorrect Section 2.6 >> Same spoto but preconfig R57 have redistribute eigrp 10 in router bgp then I remove the output not match and I ** it back again the output was match Section 2.7 >> Same spoto Section 2.8 >> Same spoto Section 2.9 >> Same spoto except preconfig lo0 on SW3-4 no have ipv6 Section 2.10 >> Same spoto Section 2.11 >> Same spoto Section 3.1 >> Same spoto Section 3.2 >> Same spoto mpls ip config on all interface alredy verify only Then I configure mpls ip mpls label protocol ldp mpls ldp router-id lo0 Section 3.3 >> Same spoto Section 3.4 >> Same spoto Section 4.1 >> Same spoto (Version ** on Apr 1,2018) Section 4.2 >> Same spoto need to configure in final section Section 5.1 – 5.4 >> Same spoto
Notes. Brussels Test Center is very good. Not found any error on exam . Keyboard & Mouse is stable . Lunch is good and Good proctor.
| 
|熊猫同学技术论坛|小黑屋|
网络工程师论坛
( 沪ICP备09076391 )
发表于 2018-4-8 17:06:43
提升卡
置顶卡
变色卡
显身卡
发表于 2018-4-8 21:35:21